Civil engineer with a number of courses in building science (aka this).
Can’t tell for sure without seeing what kind of insulation it is, but there are a few factors.
First, as other people have mentioned, having temperature gradients cause moisture issues. Typically, in modern construction in cold weather climates like Canada, we install a single waterproof layer. Cold weather, this goes inside of the insulation (between the insulation and the drywall), and in hot weather places, it’ll be installed outside the insulation.
Explanation why
The reason (simplified) for this basically boils down to hot air holds more water. As the air cools, it drops off the extra water it can no longer carry on nearby surfaces. You want to make sure hot air stays hot, and cold air stays cold. If you allow air that is hot to cool down, it will create moisture.
My understanding of the houses this is being done in, there is no vapour barrier, meaning damp+ moisture can accumulate.
Second, new houses in NA have a “minimum air exchange”, which is a specific amount of air that needs to move through the house within a given time frame, typically air changes per hour (ACH rating). This is usually accomplished by means of a central heating/ductwork units, and bedrooms are generally somewhere around 4-8, meaning all the air in the bedroom should be refreshed 4 to 8 times per hour. My understanding of many of these houses is that there is not central air system. Before the insulation, it is likely that small gaps or holes in the walls/exterior siding were sufficient to allow enough air to move through, however that air slows down when there is insulation sprayed into the cavities. Any slowdown will exacerbate moisture problems, as still air is bad. More air exchanges also would allow the house to dry out more, as evaporation would help.
Those are the general situations that would likely be a problem.
In this case, from reading the article, it seems like she has a hole in her roof, which is either new or was not caught by the installers. ANY source of water ingress would cause mold problems. The issue here is that previously, it is likely that the water trickled down the inside of the cladding (likely brick), and out at the base of the wall. Once you add insulation to that cavity, it’ll hold water and cause mold problems. Seems like a shitty spot to be in.
Civil engineer with a number of courses in building science (aka this).
Can’t tell for sure without seeing what kind of insulation it is, but there are a few factors.
First, as other people have mentioned, having temperature gradients cause moisture issues. Typically, in modern construction in cold weather climates like Canada, we install a single waterproof layer. Cold weather, this goes inside of the insulation (between the insulation and the drywall), and in hot weather places, it’ll be installed outside the insulation.
Explanation why
The reason (simplified) for this basically boils down to hot air holds more water. As the air cools, it drops off the extra water it can no longer carry on nearby surfaces. You want to make sure hot air stays hot, and cold air stays cold. If you allow air that is hot to cool down, it will create moisture.
My understanding of the houses this is being done in, there is no vapour barrier, meaning damp+ moisture can accumulate.
Second, new houses in NA have a “minimum air exchange”, which is a specific amount of air that needs to move through the house within a given time frame, typically air changes per hour (ACH rating). This is usually accomplished by means of a central heating/ductwork units, and bedrooms are generally somewhere around 4-8, meaning all the air in the bedroom should be refreshed 4 to 8 times per hour. My understanding of many of these houses is that there is not central air system. Before the insulation, it is likely that small gaps or holes in the walls/exterior siding were sufficient to allow enough air to move through, however that air slows down when there is insulation sprayed into the cavities. Any slowdown will exacerbate moisture problems, as still air is bad. More air exchanges also would allow the house to dry out more, as evaporation would help.
Those are the general situations that would likely be a problem.
In this case, from reading the article, it seems like she has a hole in her roof, which is either new or was not caught by the installers. ANY source of water ingress would cause mold problems. The issue here is that previously, it is likely that the water trickled down the inside of the cladding (likely brick), and out at the base of the wall. Once you add insulation to that cavity, it’ll hold water and cause mold problems. Seems like a shitty spot to be in.