I don’t think it’s the scheduler this time with a single CCD, but there is significant difference. These tests focus on compute and productivity with almost no games, so most of the difference could come from this bias. Another possible option is the power profile (EPP balance_performance) holding back the 7700x on linux.
The draft is pretty good. Only a few points to consider changing:
That’s a very old video format, which is definitely not HDR.
Some GPUs support the MPEG4 codec maybe try updating the driver. Did you try turning on or off Hardware acceleration for the transcodig?
Navigate to a problematic movie or episode -> 3 dots -> Get info -> right column -> Color space
Usually SDR is bt709 and HDR is bt2020. In older codecs (h264) 10 or 12 bit color depth can also cause issues.
I’m not sure how tone mapping works on plex since I don’t have a pass but with Jellyfin you need to setup OpenCL which is run on the GPU so your guess that a hardware change can break it is plausible.
green tinge to them
Are you sure it’s corrupted and not an unsupported HDR color format?
Corrupted files usually skip frames or get blocking and ghosting errors.
That’s more than enough. You can’t do any more.
As an Android flavour it should be safe after uninstalling all apps associated with the university. Did any of them need a “device owner” permission? That’s the only way to be more persistent on Android without root access.
The mobile and TV clients are often limited to the codecs with hardware acceleration. Or just selecting a lower bitrate on the client will cause transcoding.
The FS feature is great, it’s just cumbersome to use without a tool.
Snapper works well for a local backup like history both against botched updates and accidental deletion, but eats up the free space with the default settings.
Timeshift is an easy to use GUI but doesn’t support non-default partitions.
Also the quota support had a nasty side effect: freezing the whole system on snapshot deletion.
I think calling it a “cache” is not precise. The primary function of the DRAM is to hold the dictionary for translating logical addresses (e.g. sectors) from the OS to the physical addresses (which NAND chip, which bank etc.). This indirection is needed for the controller to do wear leveling without corrupting the filesystem.
On a SATA SSD without DRAM each read IO could mean 2 actual reads: first the dictionary to find the data and than the actual data being read. As you said HBM helps by eliminating this extra read.
The read and write caching is just a use of the remaining DRAM capacity. Since modern Operating Systems use the general RAM for the same function it is usually just a small increase to the throughput.
Could you tell us more specifically what do you want to use/play on this PC? (e.g browsing or productivity apps, or old games or the latest AAA titles)
A maximum budget would be very helpful.
Maybe you could use a USB keyboard or mouse connected trough a dock or OTG converter to allow file transfers.
There is an even more relevant video of using external storage trough USB. He recommends using software raid:
Are both drives fully encrypted with LUKS? Is trim enabled in both crypttab and fstab?
Thanks for the links! I updated my config from z3fold to zsmalloc and adjusted the vm.page-cluster to test these out.
Reading a bit more, I think when using large max_pool_percent (>30) with Zswap the two solutions are more similar than not. A crucial difference is what use-case is more acceptable since Zswap can cause unresponsiveness (and potential lockup) under high memory pressure. While Zram could result in an OOM crash in a similar worst-case scenario.
It is possible, it’s just not generally supported be ISP routers. Also there is a possibility of performance issues since IPv4 NAT often relies on hardware acceleration which might not work for NAT6.
Stormgate
It’s like 90% StarCraft 2 and 10% Warcraft 3. The competitive RTS part is promising but it didn’t show me anything new. Depending on the lore and campaign it may get more interesting, so far it’s neutral.
Millennia
It starts very similarly to Civ 6 with even more kinds of resources. The current version of the UI seemed confusing and the poor performance (on linux) stopped me from finishing the demo.
Even tough IPv6 is technically superior to IPv4 for the network operator it doesn’t have clear benefits for home users.
Having global addresses instead of NAT means less control over your LAN and these unique public addresses can track users more accurately.
Btrfs with compression enabled and subvolumes set.
And enable/automate maintenance services for BTRFS. For example: balace should be run on heavily used system disks or scrub could help detect errors even on single disks.
ZRAM (With proper sysctl.conf like PopOS does).
Could you explain the preference of ZRAM over ZSWAP? I thought the latter was the more advanced and better performing solution. Is there some magic in Pop’s config?
That ATX board would be great. The mATX B650M PG is also better than the previous one, it is good enough. If you can find the B650M-HDV/M.2 in stock that is even better if you don’t need 3 m.2 slots.
That monitor was indeed a lucky deal. It looks to be a good combination for this setup.